Electrical & Electronics Engineering

21/02/2019

Makani’s Energy Kites

25/01/2019

20/01/2019

13/01/2019

hi

15/07/2018

Electrical & Electronics Engineering is theworldwide community withmembers engaged in theelectrical power industry.Mission // ENERGY &POWER FOR ALL!

11/09/2015

In an alternator, at lagging power factor, the generated voltage per phase, as compared to that at unity power factor
(A) must be same as terminal voltage
(B) must be less than the terminal voltage
(C) must be more than the terminal voltage
(D) must be 1.41 time the terminal voltage.

11/09/2015

The power factor of an alternator depends on
(A) Load
(B) Speed of rotor
(C) Core losses
(D) Armature losses.

11/09/2015

DC Electric Traction System :
The transformation and high voltage generation of dc is very inconvenient to the dc supply used is at normally 600 V and this voltage is almost universal for use in urban and suburban railways. For direct current equipment, the series motor is universally employed as its speed-torque characteristics are best suited to traction requirements. Generally two or more motors are used in single equipment and these are coupled in series or in parallel to give the different running speeds required. The motors are initially connected in series with starting rheostats across the contact line and rails, the rheostats are then cut out in steps, keeping roughly constant current until the motors are running in full series. After this the motors are rearranged in parallel, again with rheostats, the rheostats are cut out in steps, leaving the motors in full parallel. The power input remains approximately constant during the series notching, then jumps to twice this value during the parallel notching. Thus a 4 motor unit will have three economical speeds when the motors are running in series, series - parallel connections. The rheostats are operated electro magnetically or electro-pneumatically.

11/09/2015

Electric Traction > AC SINGLE PHASE SYSTEM :
In this supply is taken from a single overhead conductor with the running rails. A pantograph collector is used for this purpose. The supply is transferred to primary of the transformer through on oil circuit breaker. The secondary of the transformer is connected to the motor through switchgear connected to suitable tapping on the secondary winding of the transformer.
The switching equipment may be mechanically operated tapping switch or remote controlled contractor of group switches. The switching connections are arranged in two groups usually connected to the ends of a double choke coil which lies between the collections to adjacent tapping points on the transformer. Thus the coil acts as a preventive coil to enable tapping change to be made without short circuiting sections of the transformer winding and without the necessity of opening the main circuit.

11/09/2015

Electric Traction > Advantages :
Electrical transmission, which is usually applied to high power units, has following advantages:
1. It has smooth starting without shocks.
2.Full driving torque is available from standstill.
3.Engine can be run at its most suitable speed range. This given higher efficiency range.
4.Characteristics of traction motor and generator are so chosen that the speed of the traction unit automatically adjusts according to the load and gradient so as to maintain constant output and not to overload the diesel engine.
5.Electrical transmission docs not only work as torque converter but also works as reversion gear.
Tractio n SystemEfficiencySteam locomotive
5-7%Gas turbine electric locomotive
10%Diesel electric locomotive
26-30%Electric locomotive with thermal power plant
34-36%Electrical locomotive with Hydroelectric power plant
40-42%

11/09/2015

Various systems for Traction:
1. Steam Locomotive :
This consists of a steam boiler which produces superheated steam at a pressure of 10 to 15 kg/cm2. This steam drives two double acting, non-condensing steam engines which provide the motive power for the train. The speed is controlled by regulating the flow of steam to the engine.
These engines have now become obsolete and are being gradually withdrawn from services.
2. Diesel Engines :
In these engines a multi cylinder diesel engine is. coupled to a dc generator which supplies power to the dc traction motors. These engines are available in 450 HP (shunter) to 2500 HP range. These are manufactured at Diesel Locomotive Workshops.
These engines can be easily started from cold conditions. Their availability is higher as compared to a steam engine. Also these engines have better a overall efficiency (around 25%) as compared to about 5 to 10 percent for steam locomotives.
3. Electric traction :
Here power is applied to the vehicle from an overhead wire suspended above the track.
Electric traction systems may be broadly categorized as those operating on :
1.Alternating current supply
2.Direct current supply.
In general following electric traction systems exist :
(A) AC 3 phase 3.7 kV system
(B)AC single phase 15/16 kV -161/25 Hz
(C)AC single phase 20/25 kV - 50/60 Hz
(D)DC 600 V
(E)DC 1200 V
(F)DC 1.5 kV
(G)DC 3 kV.

11/09/2015